OPTIMIZATION OF THE COMPOSITION AND PRODUCTION TECHNOLOGY OF CERAMIC ROAD SURFACES BASED ON CLAY RAW MATERIALS
DOI:
https://doi.org/10.71031/Ключевые слова:
Глина, керамическая брусчатка, керамика, Чаганская глина, физико-механические свойства, местное сырьеАннотация
The construction of ceramic road surfaces in residential complexes , private residential buildings and other socially significant facilities will lead to environmental and economic efficiency. For a comfortable life of residents, a special role is played by solving the problems of their improvement. In addition, one of the most important tasks is the improvement of sidewalks, courtyards and playgrounds, as well as the territories of squares, alleys and parks, which require a large amount of road-building materials. Currently, concrete pavers of various configurations and asphalt concrete are used to solve these problems. However, as practice shows, during the operation of these paths, their destruction is often observed.
An important technological stage in the production of ceramic materials is the preliminary preparation of raw materials, which requires significant energy and resources. As a result of research by scientists of modern technology for the production of ceramic tiles using the dry and wet method, it was found that in the process of preparing raw materials, a lot of energy and water is spent, and therefore is expensive both from an economic and environmental point of view. Scientists have proposed alternative methods for preparing raw materials, which significantly reduce energy and water.
Скачивания
Библиографические ссылки
1. Montaev S.A., Adilova N.B., Narikov K.A. Fiziko-mekhanicheskie svojstva keramicheskoj kompozicii v syr'evoj sisteme lessovidnyj suglinok-bentonit // VIIISatpaevskie chteniya: materialy Mezhdunar. nauchno-prakt. konf.-Pavlodar, 2008.-S.213-216.
2. Sulejmenov S.T., Sajbulatov S.ZH. Cennoe syr'e dlya obzhigovyh stenovyh materialov // Narodnoe hozyajstvo Kazahstana. -1979. -№7. -C.28
3. Maslennikova, G.N. Keramicheskie materialy / G.N. Maslennikova, R.A. Mamaladze, S. Midzuta, K. Koumoto. - Moskva: Strojizdat, 1991. - 320 s.
4. Montaev S.A., Pazylova S.B. Vliyanie temperatury obzhiga na izmenenie fiziko-mekhanicheskih svojstv keramicheskih mass v syr'evoj sisteme suglinok-tal'k // Nauka i obrazovanie - vedushchij faktor strategii “Kazahstan-2030”: materialy Mezhdunar. nauchn. konf.- Karaganda, 2001.- S. 45-48.
5. Sulejmenov S.T., Sajbulatov S.ZH. Cennoe syr'e dlya obzhigovyh stenovyh materialov // Narodnoe hozyajstvo Kazahstana. -1979. -№7. -C.28
6. Carter, C.B. Ceramic Materials: Science and Engineering / C.B. Carter, M.G. Norton. - Springer, 2007. - P. 4-7.
7. Ang, S.F. Sub-10-micrometer toughening and crack tip toughness of dental enamel / S.F. Ang, A. Schulz, R.P. Fernandes, G.A. Schneider // Journal of the Mechanical Behavior of Biomedical Materials. - 2011. - V. 4. - № 3. - P. 423-432.
8. Binner, J. Dense nanostructured zirconia by two stage conventional/hybrid microwave sintering / J. Binner, K. Annapoorani, A. Paul, I. Santacruz, B. Vaidhyanathan // Journal of the European Ceramic Society. - 2008. - № 28. - P. 973977.
9. Kelly, P.M. The martensitic transformation in ceramics — its role in transformation toughening / P.M. Kelly, L.R. Francis Rose // Progress in Materials Science. - 2002. - V. 47. - P. 462-557.
10. Abbas, H.A. Structural Properties of Zirconia Doped with Some Oxides / H.A. Abbas, F.F. Hamad, A.K. Mohamad, Z.M. Hanafi, M. Kilo // Diffusion Fundamentals. - 2008. - V. 8. - P. 7.1-7.8.
